How to Repair Broken Car Keys
No one enjoys calling a dealership to purchase spare parts for their vehicle. It's pricey and can take a long time to find the part you need.
To save money, you can attempt an at-home solution to your broken car key. All you need is some wire and an old paper clip.
Drill a hole into the broken end of the key
There's nothing more frustrating than a car key that is broken. It's not just a major difficulty to enter your vehicle, but it also means you won't be able to start the engine. You can fix it yourself without needing to call an expert. You can apply super glue to join the two ends of your key. This technique should only be used as a last option, because it could damage the lock or ignition.
First, you will need to trim the nail to a suitable length. It is necessary to use it as a connector, so it shouldn't be too long or too thick. Then, you can drill the hole through the broken end of your key. Make sure you drill slowly and with care. If you are not careful you could aggravate the problem. Avoid using a drill for the ignition as this can cause serious damage.
A screw or a pin can be used to pull the two ends of the chain. You could also try pliers, but be careful not to damage the car key.
Finally, you can consider using a small amount of clear tape to keep the two ends of the key together. This will stop the key from breaking and will give you a better hold on it when you pull it out.
If none of these solutions work, contact a locksmith immediately. A locksmith can remove the key from the lock of your car and supply you with a spare. They are available 24/7 and will respond promptly to your call. They can also assist you in saving money by offering a discount on key replacements. In some instances keys can be made on the spot.
Attach a connector
If your key gets damaged in the car lock it can be an absolute nightmare. You may not be able to unlock or open your car and it may cost a amount to repair. There are a few basic solutions you can use to fix the issue.
Connecting a connector is one of the best solutions to an unusable key. The connector will grab the damaged end of your key and then pull it out of the lock. It can be bought at a variety of hardware stores and is a great way to get your vehicle back on the road. But, you need to be careful while using it. Make sure it's not in the ignition lock or touching the battery.
Another option is to tear the key fob apart and carefully examine it. If you can see that the buttons seem to be damaged or out of place, try changing them. The buttons on the key fob are likely to get moved around a lot since it is used a lot.
Contacting a locksmith is an option if are unable to repair your key. A locksmith can rekey the key at your address. They can also replace the chip in the key, which is vital for newer vehicles. You can also check the warranty of your car to determine if you are able to get a key replacement.
The most common reason for a broken car key is the transponder chip in the fob has stopped working. This could cause problems starting the vehicle because the key is unable to send a signal to the ignition cylinder in the car. You can reprogramme your chip, but it is an extremely time-consuming process.
If you own a car key with a microchip, it cannot be replaced unless it is reprogrammed. This can be done by a manufacturer or dealership, but it may cost more than the services of a locksmith. Check the warranty to see whether you are eligible to receive an additional key for free.
The key can be glued together
If your car keys break, it can be a huge problem. Unlike a flat tire or a dead battery this is among the few issues that can hinder you from getting where you need to go. It is not ideal to have to use public transportation or call an acquaintance. There are options to repair your car key so you can go back to your destination.
Glues may seem like the best solution, but they're not appropriate for this scenario. The point where the key broke must withstand turning pressure and there's just not enough surface area for glue to hold it together. It is possible to glue the key back together, however, this isn't recommended unless you're an experienced automotive locksmith. It could damage your ignition tumbler and you'll need a new key.
The best option is to remove the broken part of the lock using pliers. Be careful to ensure that you don't bend the pieces of the key together and break them even more. Once you've removed the broken pieces, you'll be able to go to a locksmith or the dealership.
You could also try to repair a damaged car key by applying super glue to the two ends of the key. The broken sections should be aligned prior to applying the super glue. It is important to wait a few seconds after applying the glue prior to trying to remove the key. When the glue has dried you can test it to see if the key works.
If you don't have any tools or spare keys the only solution is to contact an auto locksmith. remote key fob repair will be able to repair the broken key quickly and effortlessly. This will save you a lot of time and money.
A professional can identify the reason for the car key breaking and help you find an effective solution. They can also give you a the new key and program it for your vehicle.
Take the key from the lock.
If part of a broken car key remains protruding from the lock, you might be able to pull it out yourself. A lot of twisting can cause damage to the lock and you will need professional assistance. To prevent this from happening start by slapping the keyway with spray graphite or oil. Then, try to grab the exposed end using the needle-nose pliers. If the pliers fail to grasp the piece of the damaged key, you may need to buy a tool that is less than $10 specially designed for this purpose and an extractor kit for keys. The kits include a variety of tools that are sized to fit in a specific keyway. Select the tool that is suitable for the lock and place it in the area just above the first cut on the damaged key. Then, use the hook of the tool to secure the key, and pull.
Another alternative is to heat a glue stick and use it to mold around the broken key. When the glue has cured it will make it easier to pull out. This method is risky because it could cause the entire key to break. Have a friend or a colleague to keep an eye on the lock when you're away if opt to employ this method.
If the lock is a standard cylinder type, it may be possible to insert a clip or pin into the back of the cylinder, and then push out the broken portion. This can be done by looking at the back of the cylinder and identifying a slot.
You can also try a key extractor tool or other tools of a specific type available in hardware stores. These tools are small enough to fit into the lock, however they're durable and can aid you in getting your broken key out of your car. Choose the appropriate size tool for your keyway, and follow the instructions.
If you're unable to use the special tools then you can try the traditional way of turning a screwdriver, or other flathead tool. Use a small enough screwdriver to fit into the lock. You could also make use of a bent paper clip to remove the damaged key from the lock on your car.